A stable, low-noise power supply is essential for high-quality music reproduction. Even modern hi-fi components with sophisticated power supplies and built-in filter stages are not entirely immune to high-frequency interference. One cause of this is capacitive coupling effects within the devices, which partially bypass the electrical isolation of the power supplies for high-frequency interference. In conjunction with the dynamic power consumption of connected components, balancing currents arise on the interconnect cables. These interfere with the sensitive audio signal and impair the purity and precision of music reproduction. Furthermore, power cables themselves emit electromagnetic interference fields that can affect nearby signal and component lines. Since these interferences have significantly higher levels compared to the very small audio signals, they have a particularly strong influence on signal processing. The Referenz AC-404 Micro AIR addresses these challenges with a cable architecture consistently designed for signal purity. The sophisticated 6-fold multicore architecture ensures exceptionally low-impedance coupling of the connected components across a wide frequency range. This effectively reduces compensation currents and creates the conditions for clean and stable signal transmission. At the same time, the design enables a powerful power supply with a high dynamic reserve — even during dynamic musical passages and high load peaks. The Micro AIR technology with an air dielectric minimizes capacitive losses and supports fast, controlled energy transfer. The result is more precise impulse reproduction and an authentic, dynamic sound presentation. The design is complemented by dual shielding consisting of a braided and foil shield. This reduces the spread of high-frequency interference fields to nearby components and interconnect cables, thereby contributing to a quiet, clean signal environment. The AC-404 Micro AIR enables music reproduction with greater clarity, detail, and dynamics—for a sound that comes as close as possible to the original recording. Click here and discover the exciting details
A stable, low-noise power supply is essential for high-quality music reproduction. Even modern hi-fi components with sophisticated power supplies and built-in filter stages are not entirely immune to high-frequency interference. One cause of this is capacitive coupling effects within the devices, which partially bypass the electrical isolation of the power supplies for high-frequency interference. In conjunction with the dynamic power consumption of connected components, balancing currents arise on the interconnect cables. These interfere with the sensitive audio signal and impair the purity and precision of music reproduction. Furthermore, power cables themselves emit electromagnetic interference fields that can affect nearby signal and component lines. Since these interferences have significantly higher levels compared to the very small audio signals, they have a particularly strong influence on signal processing. The Referenz AC-404 Micro AIR addresses these challenges with a cable architecture consistently designed for signal purity. The sophisticated 6-fold multicore architecture ensures exceptionally low-impedance coupling of the connected components across a wide frequency range. This effectively reduces compensation currents and creates the conditions for clean and stable signal transmission. At the same time, the design enables a powerful power supply with a high dynamic reserve — even during dynamic musical passages and high load peaks. The Micro AIR technology with an air dielectric minimizes capacitive losses and supports fast, controlled energy transfer. The result is more precise impulse reproduction and an authentic, dynamic sound presentation. The design is complemented by dual shielding consisting of a braided and foil shield. This reduces the spread of high-frequency interference fields to nearby components and interconnect cables, thereby contributing to a quiet, clean signal environment. The AC-404 Micro AIR enables music reproduction with greater clarity, detail, and dynamics—for a sound that comes as close as possible to the original recording. Click here and discover the exciting details
The CAT-2405 AIR is a high-end LAN cable designed for connecting audio components in streaming setups. It is based on our specially developed Air Helix construction, which enables low-loss and interference-resistant signal transmission. For this construction, we have designed a special clip that forms a stable supporting framework inside the cable. Several of these clips hold the signal pairs in a helical shape and at a defined distance freely in the air. The entire arrangement runs within a high-density shield. Two connecting bridges keep the clips evenly spaced and at the same time provide the necessary flexibility in the cable structure. Digital signal transmission: In mathematics, digital information is represented as binary values, but technically it is transmitted via analog voltage curves. To distinguish between states such as "0" and "1", voltage thresholds and time windows are defined. The transition between these states does not occur abruptly, but continuously—the signal passes through intermediate values, for example, between 0 and 5 volts. Capacitive loads, dielectric losses, noise, and external electromagnetic influences can distort these transitions. This results in timing shifts in the signal, known as jitter. Jitter makes it harder to assign data precisely in time and impairs the reconstruction of digital audio signals. Advantages of the Air Helix construction: The overall shielding made of dense braid, as well as additional foil shields for each pair of wires, effectively protect against external interference. The Air Helix construction uses air as a dielectric and ensures a constant distance between the wire pairs. This arrangement reduces crosstalk and capacitive losses, contributing to unadulterated signal transmission. Streaming components and integrated digital-to-analog converters (DACs) benefit from the improved signal quality and can process data more precisely. CAT connector with rotation mechanism: Conventional RJ45 connectors can only be plugged in at a fixed orientation. Depending on the position of the socket, this can result in unfavorable cable routing and mechanical stress on the connector, cable, and socket. To counteract this, we use rotatable RJ45 connectors with a 180° mechanism. Each connector can be rotated by about ±45°, resulting in a total adjustability of about ±90° between both connectors. This allows the cable to be routed without tension and in a space-saving manner. Sound Advantages at a Glance: Air Helix construction: Signal pairs arranged helically in air—minimal capacitive losses Air as dielectric: Reduces crosstalk and improves signal purity High-density shielding (tinned): Overall and pair shielding against electromagnetic interference RJ45 connector with 180° rotation mechanism: Flexible, tension-free cable routing Optimized for high-end streaming: Supports precise clocking in digital audio transmission Conductor material: High-purity OFC copper for stable, low-loss transmission Technical specification: CAT 8.1—up to 2000 MHz bandwidth Made in Germany: Development, manufacturing, and quality assurance on site Click here to discover exciting details
The Air Helix architecture of the Referenz Digital-2405 AIR is absolutely unique. We have developed a special clip that enables us to come as close as possible to perfect air insulation. Inside the cable, a large number of these clips form the supporting structure that keeps the helically-arranged conductors apart in the air and guides them through the shielding at a defined distance from each other. Cable flexibility is assured by means of two struts that ensure the clips remain together but also at a precise distance from one another. With coaxial cables, the shielding is generally also used as a ground wire. The Referenz Digital 2405, on the other hand, has a double-symmetric design with two positive and two negative conductors. This means that the shielding is completely separate and the signal remains free of interference. Even if it sounds paradoxical, thanks to the innovative air insulation in this cable, hi-fi becomes a simply breathtaking sound experience. Click here and discover the exciting details
The Air Helix architecture of the Referenz Digital-2405 AIR is absolutely unique. We have developed a special clip that enables us to come as close as possible to perfect air insulation. Inside the cable, a large number of these clips form the supporting structure that keeps the helically-arranged conductors apart in the air and guides them through the shielding at a defined distance from each other. Cable flexibility is assured by means of two struts that ensure the clips remain together but also at a precise distance from one another. With coaxial cables, the shielding is generally also used as a ground wire. The Referenz Digital 2405, on the other hand, has a double-symmetric design with two positive and two negative conductors. This means that the shielding is completely separate and the signal remains free of interference. Even if it sounds paradoxical, thanks to the innovative air insulation in this cable, hi-fi becomes a simply breathtaking sound experience. Click here and discover the exciting details
With the Digital-2405 AIR Pure Silver, the digital member of the AIR family is now also available as a pure silver cable. The dimensions, structure and arrangement of the conductors correspond to the respective copper versions. As with the LS-4005 AIR Pure Silver, LS-2405 AIR Pure Silver and LS-1205 Pure Silver, the signal conductors have been optimized. AIR technology is a milestone in our more than 40-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to significantly better sound reproduction, which is not only subjectively audible but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Click here and discover the exciting details
With the Digital-2405 AIR Pure Silver, the digital member of the AIR family is now also available as a pure silver cable. The dimensions, structure and arrangement of the conductors correspond to the respective copper versions. As with the LS-4005 AIR Pure Silver, LS-2405 AIR Pure Silver and LS-1205 Pure Silver, the signal conductors have been optimized. AIR technology is a milestone in our more than 40-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to significantly better sound reproduction, which is not only subjectively audible but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Click here and discover the exciting details
The LS-104 is an excellent entry-level model to the Micro AIR series. It already stands out clearly from standard cables and demonstrates the acoustic potential of this technology. Sensitive amplifiers in particular harmonize excellently with this cable. The Referenz LS-104 Micro AIR provides an open and relaxed sound. It is also available with BFA bananas or spade lugs and as an Easy Plug version. Click here and discover the exciting details
Because the speaker cable carries the largest current in the entire device chain, a suitable conductor cross-section is required to transport it with as little loss as possible. This current generates correspondingly strong magnetic fields and, since it is alternating current, there is a frequency-dependent resistance in the inductance of the cable. Low inductance is therefore particularly important for speaker cables - and this is precisely what has been achieved with the LS-1205 Air: The cable's inductance value has been reduced by a particularly ingenious arrangement of the conductors, the 4-fold "multicore" structure, enabling it to behave in a completely sound-neutral way over a wide frequency range. In addition, the magnetic fields generated around the individual conductors overlap and neutralize each other. This means that all frequencies are transported unhindered and without any time delay, enabling a fabulously open and detailed musical presentation. At the end of the air helix, the LS-1205 Air’s four conductors are separated into so-called aluminum splitters for the receiving connector. In the area between the splitters and plug, in-akustik uses highly flexible molded parts made of a special elastomer. These parts are fixed inside the splitter using a specifically designed plastic plug. This means that the cable remains reliably flexible in the connection area as well. The molded parts run right to the front of the connectors and enclose their inner workings - which underscores the sleek yet attractive design of the LS-1205 Air. Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable.
Experts have already been impressed by the LS-1204 AIR (copper). This is how AUDIO summed it up: "A stroke of genius that shows competitors how it should be done – in terms of sound, too. This was wonderfully dynamic, with the most fabulous drive reaching the speaker cones. Admittedly, the price is not low, but the acoustic yield is truly world class. What's more, everything was made by hand. You can feel the love for the product." With the LS-1205 AIR Pure Silver, the currently most filigree model in AIR technology is now also available as a pure silver cable. The structure, dimensions and conductor arrangement of this cable correspond to the copper version of the LS-1205 AIR. As with the LS-4005 AIR Pure Silver and LS-2405 AIR Pure Silver, the conductors have been optimized. Pure silver is used as the conductor material for the LS-1205 AIR Pure Silver too. Under realistic conditions, silver is currently the most conductive material. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. The electrons move 1.5 times faster than in a copper conductor! Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper.
Like the flagship model, the LS-204 is also based on Micro Air technology. The difference lies in the multicore architecture. Compared to the XL version, the LS-204 has four instead of six Concentric Copper conductors. This cable boasts an agile character and was primarily developed for slim floorstanding speakers with smaller bass drivers. The Referenz LS-204 Micro AIR is available as a single-wire version with BFA bananas or spade lugs, or as an Easy Plug version. Click here and discover the exciting details
The new Referenz Micro AIR series is a further installment in the success story of the Micro AIR technology: As with the already legendary AIR Helix cables, air is also a central component of the insulation concept in the new Referenz Micro AIR technology. Due to the low speaker impedances, however, low line resistances and a low inductance are also very important for speaker cables. For this reason, the Referenz LS-204 XL Micro AIR uses a total of 6 concentric copper conductors in addition to the air dielectric. Thanks to this multicore architecture, the magnetic fields of the positive and negative conductors overlap and neutralize each other. This significantly reduces the inductance of the cable, which guarantees unaltered transmission of the audio signal over a broad frequency spectrum. Due to our approach, the LS-204 XL has a balanced sound character with precise timing, on top of a solidly controlled foundation. This cable is primarily designed for full-size floorstanding speakers. Sound, of course, is always subjective and depends not least on the overall constellation of a hi-fi system. In the end, the decisive factor is your own personal listening impression. Click here and discover the exciting details
The LS-2405 AIR high-end speaker cable offers audiophile enthusiasts a unique sound experience. In the new Referenz LS-2405 AIR loudspeaker cable, we have taken the outstanding properties of its predecessor, the LS-2404 AIR, and developed them even further. The point-to-point Air Helix design now enables the AIR Helix architecture to be used from plug to plug and not just between the sleeves. The 360° BFA bananas and spade lugs are a further innovation, developed in-house for easy and convenient connection to the terminals. These and other technical refinements turn the already exceptional AIR cables into true masterpieces. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.
AIR technology is a milestone in our more than 46-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to a significantly better reproduction, which is not only subjectively audible, but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.
The LS-4005 AIR high-end speaker cable offers audiophile enthusiasts a unique sound experience. In the new Referenz LS-4005 AIR loudspeaker cable, we have taken the outstanding properties of its predecessor, the LS-4004 AIR, and developed them even further. The point-to-point Air Helix design now enables the AIR Helix architecture to be used from plug to plug and not just between the sleeves. The 360° BFA bananas and spade lugs are a further innovation, developed in-house for easy and convenient connection to the terminals. These and other technical refinements turn the already exceptional AIR cables into true masterpieces. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.
AIR technology is a milestone in our more than 46-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to a significantly better reproduction, which is not only subjectively audible, but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details
To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.
The LS-404 Micro AIR is a further installment in the success story of the Micro AIR technology: As with the already legendary AIR Helix cables, air is also a central component of the insulation concept in the Referenz Micro AIR technology. Due to the low speaker impedances, however, low line resistances and a low inductance are also very important for speaker cables. For this reason, the Referenz LS-404 Micro AIR uses a total of 8 concentric copper conductors in addition to the air dielectric. Thanks to this multicore architecture, the magnetic fields of the positive and negative conductors overlap and neutralize each other. This significantly reduces the inductance of the cable, which guarantees unaltered transmission of the audio signal over a broad frequency spectrum. Due to our approach, the LS-404 has an extremely balanced sound character with precise timing, on top of a solidly controlled foundation. This cable is primarily designed for full-size floorstanding loudspeakers. The impression sound makes on the listener is always subjective, of course, and depends in no small part on the overall constellation of a hi-fi system. In the end, the decisive factor is your own personal listening impression. Click here and discover the exciting details
High-end loudspeakers need power – and a lot of it, quickly and precisely. For the perfect sound the power must correspond one hundred percent with the analog image of the original sound source, be it an A cappella soloist or a stomping rock concert. A few technical tricks that help to skillfully circumvent physical influences are required to deliver this power to the loudspeaker right on time and holistically. Line resistance and line inductance play an important role with speaker cables. The powerful Referenz LS-8005 AIR has impressive 32 Cross Link Super Speed waveguides with an enormous total cross-section of 38 mm². The cross-section alone, however, does not make a good cable. The smart nesting of the conductors almost completely eliminates magnetic fields, paving the way for the finest sound facets and powerful pressure in equal measure. Good sound needs air! In developing our Air technology, we have proven that an audio cable’s insulation plays a key role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. Grounding option: The number of cell phones, WiFi routers, Bluetooth devices, PV systems and charging stations etc., is constantly increasing. This also increases the potential for electromagnetic interferences, which can affect hi-fi and high-end systems. Cables act like antennae and can transfer the interferences to the devices, where they overlay the audio signal in sensitive circuit areas, resulting in a “washed out” sound. Effective shielding and grounding concepts are crucial to protect the sound. The grounding cable of a record player is a very well-known example of this. The LS- 8005 AIR is equipped with a grounding option, which, depending on the configuration, can be connected to the amplifier’s earth, the protective conductor or earth or a grounding box, to divert disturbances. Click here and discover the exciting details
Lorem Ipsum dolor sit amet
Lorem ipsum dolor sit amet, consetetur sadipscing elitr, sed diam nonumy eirmod tempor invidunt ut labore et dolore magna aliquyam erat, sed diam voluptua. At vero eos et accusam et justo duo dolores et ea rebum. Stet clita kasd gubergren, no sea takimata sanctus est Lorem ipsum dolor sit amet. Lorem ipsum dolor sit amet, consetetur sadipscing elitr, sed diam nonumy eirmod tempor invidunt ut labore et dolore magna aliquyam erat, sed diam voluptua. At vero eos et accusam et justo duo dolores et ea rebum. Stet clita kasd gubergren, no sea takimata sanctus est Lorem ipsum dolor sit amet.
